CASE application

Adhesives & sealants

Epoxy and polyurethane routes for bonding, sealing and flexible joints.

Adhesives & sealants end use
APPLICATION TO MATERIAL

Choose the component’s role.

Explore the documented candidates and the properties relevant to their role.

90 documented candidates across 30 roles

View all matching grades

Examples show different formulation roles. Choose a role to explore alternatives for that job.

Modified polyamide / amidoamine

Dromide 9333

AHEW
190g/eq
Viscosity @ 75°C (Brookfield)
3100 - 3800cP; ASTM D 2196
Gel time @ 25°C (100 gms)
90 - 120min
Mixing ratio with epoxy resin (EEW 190)
100phr
Waterborne epoxy curing agent

Droquamine 720

AHEW
210g/eq
Viscosity @ 25°C (Brookfield)
30,000 - 50,000cP; ASTM D 2196
Gel time @ 25°C (150 gms)
50 - 70min
Mixing ratio with epoxy resin (EEW 190)
100 - 150phr
Modified aliphatic polyamine

Drocure 5194

AHEW
48g/eq
Viscosity @ 25°C (Brookfield)
50 - 240cP; ASTM D 2196
Gel time @ 25°C (100 gms)
50 - 60min
Mixing ratio with epoxy resin (EEW 190)
25phr
APPLICATION FILM · 1:45

Epoxy bonding for road studs

See how the resin and curing agent form the adhesive bond beneath a road marker.

All application films
Read the film transcript

A road stud catches the headlights. The part that holds it in place sits out of sight, between the marker and the pavement. The adhesive starts with two components. The first is a clear, solvent-free epoxy resin. The second is an amber reactive polyamide that cures the resin. For a resin with an epoxy equivalent weight of 190, the starting ratio is 50 parts hardener to 100 parts resin, by weight. Fillers and other ingredients affect the mix ratio for the finished kit. At the fixing point, prepare the pavement for the selected stud and remove loose debris. This stud design uses a drilled fixing point. The pale material on the underside is the formulated adhesive. As the marker is seated, the adhesive bed makes contact with the base and the prepared road surface. Press the stud into position and check its alignment with the road marking. Keep the reflector face clear. Good wetting helps the adhesive contact the surfaces. The polyamide also offers adhesion and resistance to water and chemicals. Check the finished bond on the actual pavement and marker base. In a laboratory test at 25 °C, a 150 g mix gels in 90–110 minutes. Reopen the lane only when the finished system meets the project's cure and traffic-release criteria. Contact D.R. Coats for samples, technical data and help developing a road-stud adhesive.

Explore selection examples
APPLICATION / MATERIAL ROUTES

Define the bond before selecting the resin.

Substrate, flexibility and processing requirements help separate suitable adhesive and sealant routes.

One-component prepolymer route2 grades to review

What shapes the choice

Compare supplied viscosity and NCO content together. A lower-viscosity grade can also have a different reactive content.

Grades to review

  • Drodur 2005

    Aromatic polyisocyanate prepolymer for one-component adhesives and sealants.

  • Drodur 2010

    Low-viscosity aromatic polyisocyanate prepolymer for one-component adhesives and sealants.

Flexible adhesive and sealant development1 grade to review

What shapes the choice

Investigate the prepolymer against the required flexibility, substrates and joint conditions.

Grades to review

  • Drodur 4005

    Highly flexible, low-viscosity prepolymer based on aromatic polyisocyanate.

MDI moisture-curing route2 grades to review

What shapes the choice

Compare the published processing viscosities, NCO ranges and curing guidance.

Grades to review

  • Drodur E21

    MDI-based aromatic polyisocyanate prepolymer for moisture-curing, one-component coatings and adhesives.

  • Drodur E23

    MDI-based aromatic polyisocyanate prepolymer for moisture-curing, one-component coatings and adhesives.

Epoxy adhesive route1 grade to review

What shapes the choice

Review the curing-agent type, mixing basis and working time for the intended bond.

Grades to review

  • Dromide 9334

    A medium-viscosity reactive polyamide curing agent for epoxy resins.

Understand the application
UNDERSTAND THE APPLICATION

Start with the bond and the joint.

A material choice becomes useful when the substrates, joint requirements and production process are defined together.

Start with the bond and the joint. A lap-bond assembly and a movement joint show two different geometry briefs. Component format and assembly/cure requirements are considered with both surfaces. Four labelled stages correspond to the text controls. Illustrative, not a system specification. BOND LINE AND JOINT GEOMETRY 1The two surfacesBonded assemblyJoint2Bond or moving joint3Reactive componentsOne- or two-component format4Assembly & cureApply → assemble → cure Illustrative joints; geometry and component format vary by application.
Start with the bond and the joint.A lap bond and a movement joint illustrate different geometry briefs. Component format and assembly/cure process are reviewed with the substrates. Simplified diagram. Full stage explanations appear in the adjacent controls.1Surfaces2Bond / jointBondJoint3ComponentsOne or twocomponents4AssemblyApply / assemblethen cure

The two surfaces

An adhesive has to interact with both surfaces. Contamination, coatings and surface treatment can change that interaction, even when the base materials have the same names.

Selection focus

Both substrates, surface preparation and any existing treatments.

Discuss this requirement

Evaluate materials in the complete formulation and intended process.

How to compare polyol selection properties →

Prepare a detailed technical brief Optional
YOUR NEXT CONVERSATION

Prepare your technical brief.

Answer only what you know. Review and edit the summary before continuing to the enquiry.

All answers are optional. Leave anything you do not know blank.

The summary updates as you answer.

Write my own enquiry

These answers prepare a discussion brief; they do not select or approve a grade. Your draft stays in this browser tab.